The Flooring Expert

Hand operated Crank arm Window Opener

Short Description:

Accessories ListSerial NumberNameNumberaHost1bGalvanized pipe1cFlat bar curved arm1dAdjustable support1eWindow sash connector1fHand rocker1gExpansion screw4hCross recessed countersunk head screw2iCross recessed pan head screw5jPin shaft2kCotter pin2lHexagon socket set screw2mLarge flat round head screw1


Product Detail

Product Tags

Outline and description of window opener

Window-Opener_DESC-(5)

Installation Steps

1. Install the window sash connector on the window sash with cross recessed pan head screws, and install the adjustable support on the window frame with cross recessed pan head screws. As shown in Figure 1

2. Fix the host on the wall with expansion screws. As shown in Figure 2

3. Firstly, put the flat rod curved arm into the galvanized pipe, then install the galvanized pipe into the main machine and fix it with pin shaft and cotter pin, then connect the flat rod curved arm with the window sash connector, fix it with pin shaft and cotter pin, and fix the flat rod curved arm on the galvanized pipe with hexagon socket set screw. As shown in Figure 3

4. Fix the hand rocker on the host with cross recessed big flat round head screws, and then fix the handle buckle on the wall with cross recessed countersunk head screws. As shown in Figure 4

Window-Opener_DESC-(6)

Installation Precautions

1. The gear box of window opener can run for one stroke before installation to check whether the gear box runs smoothly;

2. Before installing the window opener, check whether the opening stroke of the window should be greater than that of the window opener. Whether the window is opened normally;

3. When installing the adjustable support, the hole center shall be parallel to the axis of the gear shaft;

4. The window opener must be installed and debugged by professionally trained personnel who must be familiar with the technical parameter standards and safety standards of the window control system;

Precautions for use and maintenance

1. During the installation of this product, the installation personnel shall operate according to the national safety rules and regulations to ensure safety;

2. This product can not be directly installed outdoors where rainwater can be drenched;

3. This product is not equipped with anti pinch function, so attention should be paid to safety during installation and use.

4. Customers who buy our products should contact and register with us in time to obtain warranty service and after-sales maintenance service;

5. In the process of loading and unloading the window opener, ensure that the window is safe to avoid accidents

6. If the window opener is installed on a window with a height of more than 2.5m, a platform or support shall be provided for the installer;

7. If the function of the window opener is invalid and damaged, please contact the dealer or after-sales service engineer. The window opener shall not be used until it is repaired;

8. Regularly check and maintain the fixing condition of fasteners such as gearbox and support every year;

Specification Parameters
 Unit
Technical Information
Locking tension N 800
Opening angle ° 30°~70°
Push speed mm/sec 8
ambient temperature -15~+75
Protection level IP 32

1. Applicable to upper hung windows;

2. A variety of supports are available to meet different installation requirements;

3. The stroke, galvanized pipe and surface color can be customized according to the needs of customers;

Hand cranked curved arm window opener — main machine and hand cranked lower machine

Product Name Product Picture Product Drawing No Product Drawing No
Main engine (turn down to left)  host ADM-SQB002-01L Configuration for single row and single direction output
Main engine (turn down to right)  host2 ADM-SQB002-01R
Main engine (down to up)  host3 ADM-SQB002-01A Turn down the connecting machine and use it when the length of galvanized pipe exceeds 6m.
Main engine (turn down to upper left or turn down to upper right)  host4 ADM-SQB002-01B In case of double row single direction output, it is configured as the lower host, and the upper host is sqbo3a-01l / R; in case of three row single direction output, it is configured as the middle and lower host, and the upper host is sqb03a-o1l / R.
Main engine (turn down, left and right, up)  host5 ADM-SQB002-01C In case of double row bidirectional output, it is configured as the lower row host, and the upper row host is sqb03a-01d.
Main engine (turn down, left and right)  host6 ADM-SQB002-01D Single row bidirectional output configuration.
Hand cranking machine  host7 ADM-SQBO02-02 It is used together with the handle sqbo2a-o7.
Main engine (turn down to left)  host8 ADM-SQB003-01L All application scenarios are consistent with adm-sqb002-01.
Hand cranking machine  host9 ADM-SQB003-02 It is used together with the handle sqbo2a-o7.
Hand crank  host10 sQB02A-O7 It is used in combination with the manual downer sqbo2a-o2

Hand cranked curved arm window opener — Bracket/Window sash connector

Product Name Product Picture Product Drawing No Adjustment Range Product Drawing No
Bracket (fixed)
lianjiejian SQB01A-09 44mm It is used when the lianjiejian is installed on the same plane as the support.
Bracket (adjustable) lianjiejian2 SQB01A-04 90-135mm Used when the window sill width is between 50-90mm.
Bracket (adjustable) lianjiejian3 sQB01A-12 120-160mm It is used when the window sill width is between 80-110m.
Bracket (adjustable) lianjiejian4 SQB01A-14 160-200mm Use when the window sill width is between 140-160mm.
Window sash connector lianjiejian5 ADM-SQBO01-05 Conventional single curved arm (installed on the cross material of window sash) is used
Window sash connector lianjiejian6 ADM-SQB001-09 The double curved arm is normally configured and installed on the solid material of the window sash
Window sash connector – type Z lianjiejian7 SQBO1A-11 The double curved arm is normally configured and installed on the vertical material of the curtain wall opening fan (the lower hanging window adopts opposite screws in principle)
Window sash connector lianjiejian8 SQB01B-02 Use external casement type
Connecting block assembly lianjiejian9 sQBO1B-03 Used together with window sash connector sqbo1b-02

Hand cranked curved arm window opener — Flat base plate, L-shaped seat, plastic shaft sleeve, round rod curved arm, flat rod curved arm, galvanized pipe

Product Name Product Picture Product Drawing No Adjustment Range Product Drawing No
Flat backing plate xiaji SQB03A-02 99*99mm It is used when the width of the host installation position is narrower than the host installation hole
L-shaped seat xiaji2 SQB03A-03 94.5*113mm The host cannot be installed on the front, so it is used when it is installed on the side
Lower flat base plate xiaji3 ADM-SQB001-08 113*58mm It is used when the width of the installation position of the manual lower machine is narrower than the installation hole of the main machine
Lower L-shaped seat xiaji4 ADM-SQB001-10 58*128mm The manual downloader cannot be installed on the front, and it is used when it is installed on the side
Plastic shaft sleeve xiaji5 ADM-SQB001-04 Used with galvanized pipe adm-sqbo01-03.
Circular rod curved arm
xiaji6 ADM-SQB001B-01 420mm Use external casement type
550mm
670mm
Flat bar curved arm xiaji7 ADM-SQB001-06 450mm It is equipped with suspended window and internal casement window
570mm
700mm
Galvanized pipe xiaji8 ADM-SQB001-03 Outer diameter 26mm 1. As a horizontal water pipe, the host is installed on the walls on both sides of the window, and the length of galvanized pipe = window width + 5om; When the main machine is installed in the window lifter, the length of galvanized pipe = the distance from the center of the lifter to the window edge;2. As a vertical water pipe, the length of galvanized pipe = the center distance between the main machine and the lower machine – 80mm
Galvanized pipe (vertical) xiaji9 ADM-SQB001-12 Outer diameter 21mm Length of galvanized pipe = center distance between main machine and lower machine – 80mm


  • Previous:
  • Next:

  • Write your message here and send it to us